The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.
سری MHD Flasher F + G یک برنامه کامل تنظیم فلش برای BMW شما است. بر خلاف یک ماژول کمربندها، قادر به تکمیل DME کامل است در حالی که تمام مکانیسم های ایمنی نصب شده را حفظ می کند. این اجازه می دهد تا برای حداکثر عملکرد، حداکثر ایمنی، و هدایت بی نظیر.
---------------------------------------------
OBD کامل فلش:
شما می توانید MHD را در خانه نصب کنید و بلافاصله شروع به تنظیم کنید! بدون نیاز به حذف و ارسال DME خود را برای "باز کردن" هزینه است. به سادگی دانلود برنامه MHD Flasher F-سری که از طریق یک کابل K + DCAN به دستگاه اندرویدی شما و پورت OBD-II وسیله نقلیه شما متصل است، برنامه را اجرا کنید ، و در عرض 15-25 دقیقه نصب اولیه کامل است. تغییرات نقشه بیشتر خیلی سریعتر است - فقط 1-3 دقیقه! شما می توانید وسیله نقلیه خود را به فلاش OEM کارخانه در هر نقطه بازگردانید و پشتیبان گیری اولیه لازم نیست.
---------------------------------------------
مرحله 1، مرحله 2 و E85 OTS (خاموش قفسه) نقشه های PureBoost:
N55 EWG (وسایل نقلیه ساخته شده پس از 2013/07/2013 با دیجیتال الکترونیکی):
- مرحله 1 (تا 360HP / 540NM) (برای M2 و X4 M40i قابل دسترس نیست)
- مرحله 2 (تا 390HP / 580NM)
- مرحله 2+ (تا 430HP / 630NM)
- Ethanol Mix Maps: مرحله 1، 2 و 2+ E20 نقشه برای مخلوط اتانول 20٪
N55 PWG (فاضلاب پنوماتیک):
- مرحله 1 (تا 340HP / 540NM)
- مرحله 2 (تا 370HP / 580NM)
- مرحله 2+ (تا 400HP / 630NM)
- Ethanol Mix Maps: مرحله 1، 2 و 2+ E20 نقشه برای مخلوط اتانول 20٪
S55 (BMW M3 / M4 F8x):
- مرحله 1 (تا 530HP / 700NM)
- مرحله 2 (تا 560HP / 780NM)
- Ethanol Mix Maps: مرحله 1، 2 و 2+ نقشه E30 برای مخلوط اتانول 30٪
B58:
- مرحله 1 (تا 420HP / 580NM)
- مرحله 2 (تا 470HP / 630NM)
- Ethanol Mix Maps: مرحله 1، 2 نقشه برای مخلوط اتانول 30٪
---------------------------------------------
نظارت بر رفتار موتور خود را برای اطمینان از اینکه آن را کاملا با استفاده از یک تنظیم مقیاس قابل تنظیم و بسیار پاسخگو اجرا می شود. پارامترهای 50+ موتور در یک نگاه در دسترس هستند!
اینها برخی از مانیتورهای موجود هستند:
- تقویت، تقویت هدف
- لامبدا (AFR)
- دمای هوای ورودی (IAT)
- زمان سوئیچینگ در هر سیلندر
- دمای خنک کننده
- دمای روغن، فشار روغن
- دمای انتقال
- پمپ سوخت فشار بالا (HPFP)
- موقعیت دریچه گاز
- چرخه وظیفه فضایی (WGDC)
- RPM
- سرعت
- EGT
و خیلی بیشتر…
مانیتور پیشرفته MHD:
- اصلاح زمان بندی در هر سیلندر
- تقویت هدف EX که می تواند بالاتر از 22.x psi را بخواند (کانال هدف بومی تقویت BMW نمی تواند)
- محور کمپرسور پایه: نقطه تنظیم تقویت، MAF req WGDC.
- فعال گشتاور Limiters
و خیلی بیشتر…
---------------------------------------------
این گزینه های فلش را می توان به طور مستقیم از طریق برنامه به هر نقشه اعمال شد:
- اگزوز سورببل (مدت زمان و تهاجمی، سرعت حداقل، دور دقیقه دقیقه)
- سنسور نقشه N20 (در N55)
- حذف محدود کننده سرعت بالا (Vmax)
- کاهش سر و صدای سرد
- فلپ اگزوز در حالت ورزشی باز می شود
- قدرت محدود در هر دنده
- پشتیبانی XHP TCU فلش (نقشه OTS بهینه سازی شده)
حالت خنک کننده ورزشی برای خنک کننده بین کولر آب / هوا (فقط B58)
---------------------------------------------
ماشین های پشتیبانی شده:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
GT 640i GT 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive در تمام اتومبیل ها پشتیبانی می شود.
تمام اتومبیل های کیت قدرت عملکرد پشتیبانی می شوند.
برای اطلاعات بیشتر و تغییرات توصیه شده برای هر مرحله از صفحه اصلی / راهنمای کاربر ما دیدن کنید.
The MHD Flasher F+G Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 15-25 minutes the initial installation is complete. Further map changes are much faster - only 1-3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM)
- Stage 2+ (up to 430HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM)
- Stage 2 (up to 370HP/580NM)
- Stage 2+ (up to 400HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM)
- Stage 2 (up to 560HP/780NM)
- Ethanol Mix Maps: Stage 1, 2 and 2+ E30 Maps for ethanol blends of 30%
B58:
- Stage 1 (up to 420HP/580NM)
- Stage 2 (up to 470HP/630NM)
- Ethanol Mix Maps: Stage 1, 2 Maps for ethanol blends of 30%
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Boost target EX which can read higher than 22.x psi (the BMW boost target channel can't)
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
---------------------------------------------
These flash options can be applied to any map directly through the app:
- Exhaust Burble (duration & aggressiveness, min speed, min rpm)
- N20 Map Sensor (on N55)
- Remove top speed limiter (Vmax)
- Cold start noise reduction
- Exhaust flap open in sport mode
- Limit power per gear
- XHP TCU flash support (optimizied OTS maps)
- Sport cooling mode for increased water / air intercooler cooling (B58 only)
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2019
M4 S55 F82 2014 - 2019
M4 S55 F83 2014 - 2019
M140i F2x 2012 - 2019
M240i F2x 2016 - 2019
340i F3x 2015 - 2019
440i F3x 2016 - 2019
540i G3x 2017 -
640i GT G32 2017 -
740i G1x F0x 2015 -
X3 M40i G01 2017 -
X4 M40i G02 2018 -
X5 40i G05 2018 -
Z4 M40i G29 2019 -
114i F2x 2012 - 2015
116i F2x 2011 - 2015
118i F2x 2011 - 2016
120i F2x 2015 - 2017
316i F3x 2012 - 2018
X-Drive is supported on all cars.
All performance power kit cars are supported.
Check out our homepage / user manual for more information and recommended modifications for each stage.